华为MTS9510A-XA2101室外电池柜,室外通信电源柜,一体化室外电源柜
华为MTS9510A-GX2101户外综合通信电源柜
电缆应与周围的热源装置或热源区域保持至少20mm的距离,以防止加热导致绝缘层的直接损坏(熔化)或功能退化(老化或破裂)。0电缆弯曲半径要求:不小于电缆直径的5倍。
类似的电缆应绑在一起,不同类型的电缆应相距至少30mm。禁止相互缠绕或交叉铺设。
绑扎后的电缆应紧密包装在一起,外观应平直整齐,不得损伤皮肤。
保护接地线不应与信号线绑在一起或相互缠绕。有必要保持一定的距离以减少干扰。
交流线、直流线、信号线和通信线需要单独捆扎,不能捆扎在一起。
在电源线的铺设过程中,严禁缠绕或扭曲。如果发现电源线长度不足,应更换电源线,电源线中不得有接头或焊点。
MTS9510A-GX2101.jpg文件
华为MTS9510A-GX2101室外基站通信交换机电源柜
华为MTS9510A-GX2101用于符合设计规范的环境(如电网、输入电压、温度、湿度等),否则可能会导致产品故障,导致产品功能异常或不在产品范围内的部件损坏。
在对本产品进行各种操作时,必须严格遵守华为提供的相关设备注意事项和特殊安全说明。负责安装和维护华为设备的人员在安装、操作和维护设备之前,必须经过严格的培训,了解各种安全注意事项,掌握正确的操作方法。华为对违反一般安全操作要求和设备安全标准不承担任何责任。
机柜前配电箱应有保护开关装置,规格不应低于机柜本身的输入开关。
操作员应遵守当地法规和规范。本手册中的安全注意事项只是对当地安全法规的补充。
禁止在雷雨天气下操作设备和电缆。
禁止将设备放置在有易燃、易爆气体或烟雾的环境中,因为有大量的红外辐射、有机溶剂和腐蚀性气体。
禁止用水清洗设备的内部或外部电气部件。
禁止将安全超低电压(SELV)电路端子连接到通信网络电压(TNV)电路终端。
操作时严禁将手表、手镯、戒指等易导电物品佩戴在手腕上。
操作过程中必须使用专用绝缘工具。
应使用扭矩扳手固定螺钉,并用红色和蓝色标记进行双重检查。安装人员确认螺钉已拧紧后,在螺钉上涂上蓝色标记;检查人员确认拧紧后,会出现红色标记。
安装或维护操作必须遵守任务的步骤顺序,未经制造商许可,不得改变设备的结构和安装顺序。
在接触任何导体表面或端子之前,使用电表测量接触点的电压,并确认接触点没有电压或电压在预定范围内。
安装或拆卸电力电缆时,确保断开相应的电路,以防止产生电弧或火花。
如果交流输入电缆从顶部连接到机柜,则在进入机柜之前,必须在机柜外部使用U形弯头。
MTS9510A-GX2101A.jpg






Huawei MTS9510A-GX2101 Outdoor Integrated Communication Power Cabinet
The cable should be kept at a distance of at least 20mm from the surrounding heat source device or heat source area to prevent direct damage (melting) or functional degradation (aging or rupture) of the insulation layer caused by heating. 0 Cable bending radius requirement: not less than 5 times the cable diameter.
Similar cables should be tied together, and different types of cables should be laid at least 30mm apart. It is prohibited to wrap or cross lay each other.
The cables after binding should be tightly packed together, with a straight and neat appearance and no skin damage.
The protective ground wire should not be tied together with the signal wire or intertwined with each other. It is necessary to maintain a distance to reduce interference.
AC lines, DC lines, signal lines, and communication lines need to be tied separately and cannot be tied together.
During the laying process of the power cord, it is strictly prohibited to wrap or twist it. If the length of the power cord is found to be insufficient, it should be replaced and no joints or solder joints should be made in the power cord.
MTS9510A-GX2101.jpg
Huawei MTS9510A-GX2101 outdoor base station communication switch power cabinet
Huawei MTS9510A-GX2101 is used in an environment that meets the design specifications (such as power grid, input voltage, temperature, humidity, etc.), otherwise it may cause product malfunction, resulting in abnormal product functionality or component damage that is not within the scope of the product.
When performing various operations on this product, it is necessary to strictly follow the relevant equipment precautions and special safety instructions provided by Huawei. Personnel responsible for installing and maintaining Huawei equipment must undergo strict training, understand various safety precautions, and master the correct operating methods before installing, operating, and maintaining the equipment. Huawei does not assume any responsibility for violating the general safety operation requirements and equipment safety standards.
The front distribution box of the cabinet should have protective switch devices, and the specifications should not be less than the input switches of the cabinet itself.
Operators should comply with local regulations and norms. The safety precautions in the manual are only a supplement to local safety regulations.
It is prohibited to operate equipment and cables in thunderstorm weather.
It is prohibited to place the equipment in an environment with flammable, explosive gases or smoke, as there is a large amount of infrared radiation, organic solvents, and corrosive gases.
It is prohibited to use water to clean the internal or external electrical components of the equipment.
It is prohibited to connect the safety ultra-low voltage (SELV) circuit terminal to the communication network voltage (TNV) circuit terminal.
It is strictly prohibited to wear easily conductive objects such as watches, bracelets, rings, etc. on the wrist during operation.
Special insulation tools must be used during operation.
The screws should be fixed using a torque wrench and double checked with red and blue markings. After the installation personnel confirm that the screws are tightened, paint blue markings on the screws; After the inspector confirms the tightening, the red mark will appear.
Installation or maintenance operations must comply with the step sequence of the task, and do not change the structure and installation sequence of the equipment without the permission of the manufacturer.
Before touching any conductor surface or terminal, use an electric meter to measure the voltage at the contact point and confirm that there is no voltage at the contact point or that the voltage is within the predetermined range.
When installing or removing power cables, ensure that the corresponding circuit is disconnected to prevent the generation of electric arcs or sparks.
If the AC input cable is connected to the cabinet from the top, it must be U-bent outside the cabinet before entering the cabinet.
MTS9510A-GX2101A.jpg