18611994737

首页 >> 产品中心 >>华为室外柜 >> 华为MTS9000A室外通信电源机柜 空调1500W 高频开关电源
详细说明

华为MTS9000A室外通信电源机柜 空调1500W 高频开关电源

暂无价格
  • 产品说明
  • 产品参数

华为MTS9000A室外通信电源机柜  空调1500W 高频开关电源

华为MTS9000A室外通信电源机柜  空调1500W 高频开关电源

华为MTS9000A户外电源网络机柜
服务器电源的总线电压和效率
目前使用的服务器电源主要有两种类型。一种类型是没有功率因数校正的传统硬开关电源(ATX和SSI标准),主要使用单端正向或半桥拓扑,效率在70%到85%之间。由于其硬开关技术,其开关损耗在低输入电压(高输入电流)和高输入电压下都很高,在额定电压和220VAC负载下效率很高。因此,高压直流输电的浮充应该更适合275V。过高的母线电压不仅降低了效率,而且威胁到开关管的安全工作区域。较高的直流电压不应超过350V。
另一种类型的服务器电源是添加了APFC的高功率因数电源。这种类型的电源实际上是两级转换,其中级*是APFCBOOST转换器,级*是DC/DC转换器。由于BOOST转换器的效率与输入电压范围之间的关系有限,可以考虑使用更大的400V或282V直流电压。如果使用400V直流电压,可以取消BOOST转换器以升级和改善服务器电源。如果使用282V直流电压,则无论使用何种服务器电源,都无需更改。
(2) 高压直流输电电源模块的电压调节
目前用于高压直流输电的功率模块均来自功率操作电源,其特点是三相三线制、无源功率因数校正和功率因数约为0.92和286V的高输出电压。由于模块功率密度的限制,当输出电压增加时,必须降低输出电流,即恒定功率输出。由于输出整流管耐压和输出电解电容器耐压的限制,较大的输出电压只能调节到320V。否则,设计变更过于重大,需要重新设计。
(3) 高压直流输电中绝缘监测的必要性
MTS9000(2)尽管高压直流电压的峰值与交流电压相比并不高,但由于零交流电压的存在,jpg的危险性远大于高压直流电压。因此,为了确保操作人员的人身安全,有必要在高压直流输电中增加绝缘监测功能。绝缘监测仪器应放置在柱柜中,以定位分支机构。
1) 绝缘监测的选择
绝缘监测有三种形式,即平衡电桥法、小信号注入法和漏电流检测法。平衡电桥法简单可靠,但只能检测母线对地绝缘不良,无法定位支路;小信号注入方法容易产生共模干扰,漏电流检测方法是更好的选择。缺点是当有很多分支机构时,成本会更高。
2) 泄漏电流绝缘监测仪的工作原理
首先,检查母线是否与地面平衡。如果不平衡,则分别切换检测电阻器,以测量每个支路的泄漏电流。根据泄漏电流,可以定位支路并计算绝缘电阻值。
(4) 熔断器和空气开关的组合用于保护,末端由直流空气开关和交流空气开关的结合进行保护。不要连接到常规插座。
(5) 当IT设备内部配置多个电源模块时,必须由多个分流开关控制,禁止一个分流空气开关控制多个电源组件。
3.节能案例计算
作为解决方案的一个例子,将高压直流电源系统与使用大容量系统的交流UPS系统进行比较,并在相同的大容量电源要求下,比较新建的交流UPS并联系统与高压直流系统之间的投资差异。
高压直流系统与不间断电源系统的投资比较
DUM通信电源系统采用我公司开发的新型智能高频开关整流模块和监控系统,符合国家相关标准和要求。适用于中小型程控交换机、移动通信、卫星通信地面站、微波通信等设备的供电,也可用于其他通信设备的供电。

Huawei MTS9000A Outdoor Power Network Cabinet
Bus voltage and efficiency of server power supply
There are currently two main types of server power supplies used. One type is traditional hard switching power supplies without power factor correction (ATX and SSI standards), mainly using single ended forward or half bridge topologies, with efficiency ranging from 70% to 85%. Due to its hard switching technology, its switching loss is high at both low input voltage (high input current) and high input voltage, and its efficiency is high at rated voltage and load of 220VAC. Therefore, the float charging of high-voltage direct current transmission should be more suitable for 275V. Excessive bus voltage not only reduces efficiency, but also threatens the safe working area of the switch tube. The higher DC voltage should not exceed 350V.
Another type of server power supply is a high power factor power supply with added APFC. This type of power supply is actually a two-stage conversion, with stage * being the APFCBOOST converter and stage * being the DC/DC converter. Due to the limited relationship between the efficiency of BOOST converters and the input voltage range, it is possible to consider using a larger 400V or 282V DC voltage. If a 400V DC voltage is used, the BOOST converter can be cancelled to upgrade and improve the server power supply. If 282V DC voltage is used, no matter what server power supply is used, there is no need to change it.
(2) Voltage Adjustment of High Voltage Direct Current Transmission Power Module
The power modules currently used in high-voltage direct current transmission are all from power operated power sources, characterized by three-phase three-wire system, passive power factor correction, and high output voltages with power factors of approximately 0.92 and 286V. Due to the limitation of module power density, when the output voltage increases, the output current must be reduced, i.e. constant power output. Due to the limitation of output rectifier tube withstand voltage and output electrolytic capacitor withstand voltage, the larger output voltage can only be adjusted to 320V. Otherwise, the design change is too significant and needs to be redesigned.
(3) The necessity of insulation monitoring in high-voltage direct current transmission
MTS9000(2)。 Although the peak value of high-voltage DC voltage is not high compared to AC voltage, the danger of jpg is much greater than that of high-voltage DC voltage due to the presence of zero AC voltage. Therefore, in order to ensure the personal safety of operators, it is necessary to add insulation monitoring function in high-voltage direct current transmission. Insulation monitoring instruments should be placed in column cabinets to locate branches.
1) Selection of insulation monitoring
There are three forms of insulation monitoring, namely balanced bridge method, small signal injection method, and leakage current detection method. The balanced bridge method is simple and reliable, but it can only detect poor insulation of the busbar to the ground and cannot locate the branch; Small signal injection methods are prone to common mode interference, and leakage current detection methods are a better choice. The disadvantage is that when there are many branches, the cost will be higher.
2) Working principle of leakage current insulation monitoring instrument
Firstly, check if the busbar is balanced against the ground. If it is unbalanced, switch the detection resistors separately to measure the leakage current of each branch. Based on the leakage current, the branch can be located and the insulation resistance value can be calculated.
(4) The combination of fuse and air switch is used for protection, and the end is protected by a combination of DC air switch and AC air switch. Do not connect to regular sockets.
(5) When multiple power modules are configured inside IT equipment, they must be controlled by multiple shunt switches, and it is prohibited for one shunt air switch to control multiple power components.
3. Calculation of energy-saving cases
As an example of a solution, compare the high-voltage DC power supply system with an AC UPS system using a high-capacity system, and compare the investment differences between the newly built AC UPS parallel system and the high-voltage DC system under the same high-capacity power supply requirements.
Investment Comparison between High Voltage DC System and Uninterruptible Power Supply System
The DUM communication power system adopts a new intelligent high-frequency switch rectifier module and monitoring system developed by our company, which meets relevant national standards and requirements. Suitable for the power supply of small and medium-sized program-controlled switches, mobile communication, satellite communication ground stations, microwave communication and other equipment, and can also be used for the power supply of other communication equipment.

华为MTS9000A室外通信电源机柜  空调1500W 高频开关电源

华为MTS9000A室外通信电源机柜  空调1500W 高频开关电源

华为MTS9000A户外电源网络机柜
服务器电源的总线电压和效率
目前使用的服务器电源主要有两种类型。一种类型是没有功率因数校正的传统硬开关电源(ATX和SSI标准),主要使用单端正向或半桥拓扑,效率在70%到85%之间。由于其硬开关技术,其开关损耗在低输入电压(高输入电流)和高输入电压下都很高,在额定电压和220VAC负载下效率很高。因此,高压直流输电的浮充应该更适合275V。过高的母线电压不仅降低了效率,而且威胁到开关管的安全工作区域。较高的直流电压不应超过350V。
另一种类型的服务器电源是添加了APFC的高功率因数电源。这种类型的电源实际上是两级转换,其中级*是APFCBOOST转换器,级*是DC/DC转换器。由于BOOST转换器的效率与输入电压范围之间的关系有限,可以考虑使用更大的400V或282V直流电压。如果使用400V直流电压,可以取消BOOST转换器以升级和改善服务器电源。如果使用282V直流电压,则无论使用何种服务器电源,都无需更改。
(2) 高压直流输电电源模块的电压调节
目前用于高压直流输电的功率模块均来自功率操作电源,其特点是三相三线制、无源功率因数校正和功率因数约为0.92和286V的高输出电压。由于模块功率密度的限制,当输出电压增加时,必须降低输出电流,即恒定功率输出。由于输出整流管耐压和输出电解电容器耐压的限制,较大的输出电压只能调节到320V。否则,设计变更过于重大,需要重新设计。
(3) 高压直流输电中绝缘监测的必要性
MTS9000(2)尽管高压直流电压的峰值与交流电压相比并不高,但由于零交流电压的存在,jpg的危险性远大于高压直流电压。因此,为了确保操作人员的人身安全,有必要在高压直流输电中增加绝缘监测功能。绝缘监测仪器应放置在柱柜中,以定位分支机构。
1) 绝缘监测的选择
绝缘监测有三种形式,即平衡电桥法、小信号注入法和漏电流检测法。平衡电桥法简单可靠,但只能检测母线对地绝缘不良,无法定位支路;小信号注入方法容易产生共模干扰,漏电流检测方法是更好的选择。缺点是当有很多分支机构时,成本会更高。
2) 泄漏电流绝缘监测仪的工作原理
首先,检查母线是否与地面平衡。如果不平衡,则分别切换检测电阻器,以测量每个支路的泄漏电流。根据泄漏电流,可以定位支路并计算绝缘电阻值。
(4) 熔断器和空气开关的组合用于保护,末端由直流空气开关和交流空气开关的结合进行保护。不要连接到常规插座。
(5) 当IT设备内部配置多个电源模块时,必须由多个分流开关控制,禁止一个分流空气开关控制多个电源组件。
3.节能案例计算
作为解决方案的一个例子,将高压直流电源系统与使用大容量系统的交流UPS系统进行比较,并在相同的大容量电源要求下,比较新建的交流UPS并联系统与高压直流系统之间的投资差异。
高压直流系统与不间断电源系统的投资比较
DUM通信电源系统采用我公司开发的新型智能高频开关整流模块和监控系统,符合国家相关标准和要求。适用于中小型程控交换机、移动通信、卫星通信地面站、微波通信等设备的供电,也可用于其他通信设备的供电。

Huawei MTS9000A Outdoor Power Network Cabinet
Bus voltage and efficiency of server power supply
There are currently two main types of server power supplies used. One type is traditional hard switching power supplies without power factor correction (ATX and SSI standards), mainly using single ended forward or half bridge topologies, with efficiency ranging from 70% to 85%. Due to its hard switching technology, its switching loss is high at both low input voltage (high input current) and high input voltage, and its efficiency is high at rated voltage and load of 220VAC. Therefore, the float charging of high-voltage direct current transmission should be more suitable for 275V. Excessive bus voltage not only reduces efficiency, but also threatens the safe working area of the switch tube. The higher DC voltage should not exceed 350V.
Another type of server power supply is a high power factor power supply with added APFC. This type of power supply is actually a two-stage conversion, with stage * being the APFCBOOST converter and stage * being the DC/DC converter. Due to the limited relationship between the efficiency of BOOST converters and the input voltage range, it is possible to consider using a larger 400V or 282V DC voltage. If a 400V DC voltage is used, the BOOST converter can be cancelled to upgrade and improve the server power supply. If 282V DC voltage is used, no matter what server power supply is used, there is no need to change it.
(2) Voltage Adjustment of High Voltage Direct Current Transmission Power Module
The power modules currently used in high-voltage direct current transmission are all from power operated power sources, characterized by three-phase three-wire system, passive power factor correction, and high output voltages with power factors of approximately 0.92 and 286V. Due to the limitation of module power density, when the output voltage increases, the output current must be reduced, i.e. constant power output. Due to the limitation of output rectifier tube withstand voltage and output electrolytic capacitor withstand voltage, the larger output voltage can only be adjusted to 320V. Otherwise, the design change is too significant and needs to be redesigned.
(3) The necessity of insulation monitoring in high-voltage direct current transmission
MTS9000(2)。 Although the peak value of high-voltage DC voltage is not high compared to AC voltage, the danger of jpg is much greater than that of high-voltage DC voltage due to the presence of zero AC voltage. Therefore, in order to ensure the personal safety of operators, it is necessary to add insulation monitoring function in high-voltage direct current transmission. Insulation monitoring instruments should be placed in column cabinets to locate branches.
1) Selection of insulation monitoring
There are three forms of insulation monitoring, namely balanced bridge method, small signal injection method, and leakage current detection method. The balanced bridge method is simple and reliable, but it can only detect poor insulation of the busbar to the ground and cannot locate the branch; Small signal injection methods are prone to common mode interference, and leakage current detection methods are a better choice. The disadvantage is that when there are many branches, the cost will be higher.
2) Working principle of leakage current insulation monitoring instrument
Firstly, check if the busbar is balanced against the ground. If it is unbalanced, switch the detection resistors separately to measure the leakage current of each branch. Based on the leakage current, the branch can be located and the insulation resistance value can be calculated.
(4) The combination of fuse and air switch is used for protection, and the end is protected by a combination of DC air switch and AC air switch. Do not connect to regular sockets.
(5) When multiple power modules are configured inside IT equipment, they must be controlled by multiple shunt switches, and it is prohibited for one shunt air switch to control multiple power components.
3. Calculation of energy-saving cases
As an example of a solution, compare the high-voltage DC power supply system with an AC UPS system using a high-capacity system, and compare the investment differences between the newly built AC UPS parallel system and the high-voltage DC system under the same high-capacity power supply requirements.
Investment Comparison between High Voltage DC System and Uninterruptible Power Supply System
The DUM communication power system adopts a new intelligent high-frequency switch rectifier module and monitoring system developed by our company, which meets relevant national standards and requirements. Suitable for the power supply of small and medium-sized program-controlled switches, mobile communication, satellite communication ground stations, microwave communication and other equipment, and can also be used for the power supply of other communication equipment.


电话直呼
在线客服
在线留言
发送邮件
联系我们:
18611994737
客服1
点击这里给我发消息
还可输入字符250(限制字符250)
技术支持: 建站ABC | 管理登录
×
seo seo