维蒂ECM3-BBU室外柜,高频开关电源柜,室外一体化电源柜
维蒂ECM3-BBU室外柜,
一般安全注意事项
本产品应按照设计规范(如电网、输入电压、温度、湿度等)使用,否则可能导致产品故障,导致产品功能异常或不在产品范围内的部件损坏。
负责安装和维护华为设备的人员在安装、操作和维护设备之前,必须经过严格的培训,了解各种安全注意事项和正确的操作方法。
操作员应遵守当地法规和规范。本手册中的安全注意事项只是对当地安全法规的补充。
禁止在雷雨天气下操作设备和电缆。
雨后维护室外设备时,需要轻轻打开柜门,并清洁柜门缝隙周围的水,以防止在开门和关门时飞溅物进入机柜。
操作时严禁将手表、手镯、手镯、戒指等易导电物品佩戴在手腕上。
操作过程中必须使用专用绝缘工具。
根据数据的扭矩要求,应使用扭矩工具拧紧螺钉,并使用红色和蓝色标记进行双重检查。安装人员确认螺钉已拧紧后,应在螺钉上涂上蓝色标记。检查人员确认螺钉已拧紧后,应涂上红色标记。
安装或维护操作必须遵循任务的步骤顺序。
在接触任何导体表面或端子之前,使用电表测量接触点的电压,并确认接触点没有电压或电压在预定范围内。
如果交流输入电缆从机柜顶部连接到机柜,则需要在机柜外部弯曲成U形。
如果电源系统未连接到电池或电池容量不足,则负载(电气设备)可能在维护或故障期间断电。
如果电缆的储存温度低于零摄氏度,则在铺设和铺设操作之前,必须将电缆移至室温下储存至少24小时。
设备安装完成后,用户应按照用户手册的要求对设备进行日常检查和维护,并及时更换
一个×32A/1P2×20A/1P二次掉电分支空气开关2×32A/1P3×16A/1P,1×10A/1P直流防雷10kA/20kA,8/20μ整流模块PSU/太阳能模块SSU额定功率3000W(Vac~Vac)效率PSU>96%*;SSU高达985%尺寸105mm(宽)×281mm深×408mm(高),重量≤2kg,监控模块信号输入:5个模拟量(电池温度、温度、湿度、温度1、温度2),9个开关量(浸水、烟雾感应、门磁。6个公共输入),报警输出:8个干触点通信端口RS232。
MTS9000A的适用性支持多种能源的集成,包括市政电力、石油发动机、太阳能和高压直流电。通过系统转换,它可以。以多种格式输出。包括-48V直流、220V交流、高压直流远程电源等介绍可选配件。城市电力、太阳能、柴油发电机、高压直流输电。MTS9000A,-48V,高压直流,>500m-48V,直流,<300m,交流RRU,-48V本地,直流RRU,220V,交流,电源。BBU,变速器。电池支持多种能量输入,使站点更易于访问。一体化监控单元,可靠性高,简化网络建设计划,简化备件管理。
纯光场景在0℃~+45℃之间(记得在下面安装光伏板,避免阳光直射),海拔要求在0M~4000MM之间(在2000MM~4000MM时,需要高温降额,每增加200M,工作温度降低1℃),噪声级符合GB487的要求,防护等级和工作要求为IP34,B级。华为ESC330-D5户外通信电源柜应满足无导电粉尘、腐蚀性气体、危险源、有害生物、霉菌等指标的要求。华为RFC应用情况:分布式、4路掉电输出RRU 3 10A空气开关应使用与空气开关备注对应的直流输出直流电源单元。当APM30为3个RRU供电时,3个10A空气开关分别控制3个直流输出







General safety precautions
This product should be used in accordance with the design specifications (such as power grid, input voltage, temperature, humidity, etc.), otherwise it may cause product malfunction, resulting in abnormal product functionality or component damage that is not within the scope of the product.
Personnel responsible for installing and maintaining Huawei equipment must undergo strict training, understand various safety precautions, and correct operating methods before installing, operating, and maintaining the equipment.
Operators should comply with local regulations and norms. The safety precautions in the manual are only a supplement to local safety regulations.
It is prohibited to operate equipment and cables in thunderstorm weather.
When maintaining outdoor equipment after rain, it is necessary to gently open the cabinet door and clean the water around the cabinet door gap to prevent splashes from entering the cabinet during door opening and closing.
It is strictly prohibited to wear easily conductive objects such as watches, bracelets, bracelets, rings, etc. on the wrist during operation.
Special insulation tools must be used during operation.
According to the torque requirements of the data, torque tools should be used to tighten the screws, and red and blue markings should be used for double inspection. After the installation personnel confirm that the screws are tightened, blue markings should be painted on the screws. After the inspection personnel confirm that the screws are tightened, red markings should be painted.
Installation or maintenance operations must follow the step sequence of the task.
Before touching any conductor surface or terminal, use an electric meter to measure the voltage at the contact point and confirm that there is no voltage at the contact point or that the voltage is within the predetermined range.
If the AC input cable is connected to the cabinet from the top of the cabinet, it needs to be bent in a U-shape outside the cabinet.
If the power system is not connected to a battery or the battery capacity is insufficient, it is possible for the load (electrical equipment) to power down during maintenance or failure.
If the storage temperature of the cable is below zero degrees Celsius, the cable must be moved to room temperature for storage for at least 24 hours before laying and laying operations.
After the installation of the equipment is completed, users should conduct routine inspections and maintenance of the equipment in accordance with the requirements of the user manual, and promptly replace it
one × 32A/1P。 two × 20A/1P secondary power down branch air switch 2 × 32A/1P。 three × 16A/1P,1 × 10A/1P DC lightning protection 10kA/20kA, 8/20 μ Rectifier module PSU/solar module SSU rated power 3000W (Vac~Vac) efficiency PSU>96% *; SSU up to 985% size 105mm (width) × 281mm deep × 408mm (height), weight ≤ 2kg, monitoring module signal input: 5 analog quantities (battery temperature, temperature, humidity, temperature 1, temperature 2), 9 switching quantities (water immersion, smoke sensing, door magnetic. 6 public inputs), alarm output: 8 dry contact communication ports RS232.
The applicability of MTS9000A supports the integration of multiple energy sources, including municipal electricity, oil engines, solar energy, and high-voltage direct current. Through system transformation, it can. Output in multiple formats. Including -48V DC, 220V AC, high-voltage DC remote supply, etc. Introduction。 Optional accessories. City power, solar energy, diesel generator, HVDC. MTS9000A, -48V, high-voltage DC,>500m- 48V, DC,<300m, AC RRU, -48V, local, DC RRU, 220V, AC, power supply. BBU, transmission. Battery. Support multiple energy inputs, making the site easier to access. Integrated monitoring and control unit, high reliability, simplified network construction plan, and simpler spare parts management.
The pure light scene is between 0 ℃~+45 ℃ (remember to install the PV board below to avoid direct sunlight), the altitude is required to be between 0M~4000MM (at 2000MM~4000MM, the high temperature derating is required, and the operating temperature is reduced by 1 ℃ for every 200M increase), the noise level meets the requirements of GB487, the protection level and working requirements are IP34, Class B, The Huawei ESC330-D5 outdoor communication power supply cabinet should meet the requirements of being free from conductive dust, corrosive gases, hazards, harmful organisms, molds, and other indicators. Huawei Huawei RFC application situation: DC output DC power supply unit corresponding to air switch remarks should be used for distributed, 4-way power down output RRU 3 10A air switches. When APM30 supplies power to 3 RRUs, 3 10A air switches control 3 DC outputs respectively